
Some links on this page are Amazon affiliate links. If you buy through them we may earn a commission at no extra cost to you. It does not change what we recommend.
There is a clip for every surface, which means there is never a good reason to use a nail, a staple or a drawing pin.
The reason to care is not the holes. It is that a staple driven through or beside a cord compresses the insulation, and compressed insulation is where a short circuit starts — outdoors, in the wet, in a place you cannot see. The damage does not announce itself the year you do it.
Match the clip to the surface
Gutters. All-purpose or "shingle and gutter" clips hook over the gutter lip. Most have two orientations, so you can point bulbs outward at the street or upward along the roof. Decide which before you start: changing your mind halfway along a run is visible from the pavement.
Shingles. Shingle tab clips slide under the edge of a shingle and grip it. They need no fixing at all and leave nothing behind. Do not force one under a brittle shingle in cold weather — asphalt gets fragile below freezing and will crack rather than flex.
Brick and mortar. Brick clips grip the vertical mortar joint between bricks. They are sized for standard joints, so measure yours before buying a hundred of them. For a surface you cannot clip, outdoor adhesive hooks work on clean, dry brick, but not reliably in freezing temperatures.
Vinyl or aluminium siding. Siding hooks slip into the lip where one course overlaps the next. No holes, no adhesive, and they come off in spring without a mark.
Stucco, render and concrete. This is the hard one — nothing clips to it. Options are outdoor adhesive hooks on a clean dry surface, or small masonry anchors left permanently in place so that future years are a hanging job rather than a drilling job. Many people do the second once and are glad of it.
Glass and uPVC windows. Suction cups with hooks, on the inside. On the outside they fail in cold weather.
Gutterless eaves and fascia. Fascia clips screw into the board, which does mean a small hole; alternatively run a length of wire or a thin cable along the fascia once, fixed at the ends, and clip lights to the wire each year.
- All-purpose gutter and shingle clipsThe two surfaces most rooflines need; buy a box more than you calculatedSee options on Amazon
- Brick clipsGrip the mortar joint; check your joint width before buying in bulkSee options on Amazon
- Siding hooksFor vinyl and aluminium siding laps; no holes at allSee options on Amazon
- Outdoor adhesive hooksFor stucco, render and painted surfaces where nothing clipsSee options on Amazon
Buy more clips than you worked out
Clips are cheap, they go missing in grass, they break when cold, and the spacing you plan on paper is never the spacing you use. Run them every 12 inches or so for a straight line — wider, and the string sags visibly between them, which no amount of care in hanging will hide.
A gentle sag between bulbs reads as decoration. A sag between clips reads as a job half done.
Work from the ground where you can
A telescoping light-hanging pole fits a clip onto a gutter from ground level and takes it off again in January. It is slower than working from a ladder and far better than falling off one. For a single-storey frontage it can do the whole job.
Where a ladder is unavoidable: fibreglass rather than aluminium near electricity, one foot out for every four feet up, hips between the rails, and someone who knows you are up there. Moving the ladder six times is the correct amount of effort; stretching sideways once is not.
Run your own numbers
The calculator does the arithmetic on this page for your own measurements — trees, rooflines, columns, railings, shrubs and windows.
Open the calculatorThe method that saves the most time
Lay the whole run out on the ground first. Plug it in, confirm every bulb lights, and only then start hanging. Finding a dead section after an hour on a ladder is a particular kind of annoyance.
Start at the outlet and work away from it. Then the male plug is at the end you need it, instead of forty feet from the nearest socket.
Clip the lights to the string, not the string to the clips. Attach clips along the cord on the ground, spaced as you want them, then hang the assembly. Fiddling with individual clips at the top of a ladder is where the time goes.
Never pull a run tight to make it reach. Tension on a cord at a socket is how a connection fails. If a run is short, a short outdoor-rated extension cord costs less than the string.
Three things never to do
- Drive a nail or staple through, or hard against, a cord. Crushed insulation is a fault waiting for weather.
- Hang anything from the overhead service line where power enters the house, or work near it with a ladder or pole.
- Leave them up all year. UV breaks down insulation and clips work loose in wind. The lights that fail dangerously are usually the ones that never came down.
Last reviewed November 2026.